Car keys · Toronto
Ignition Lock Repair
A scrape sits beside the ignition slot, left by whoever tried the vehicle overnight in the driveway. The key that used to start it now does nothing at all, and the housing itself feels looser than it should.
Ignition Lock Repair
In plain words
Where the hardware allows it, a replacement or serviced ignition cylinder is pinned to match the key already in your pocket, rather than handing you a second key to keep track of. The same thinking extends to the doors and trunk: if they already share a key with the ignition, the locksmith keeps that arrangement intact, so one key still does everything it did before the visit began.
How the visit goesThe key slides in fine and turns without any resistance at all, and the dash lights flicker, but nothing catches. No click, no crank, just a key spinning loosely in a slot that used to grab hold of it properly.
Toronto
How the visit goes
Checking the switch positions and the steering lock
Behind the part of the ignition a key touches sits an electrical switch with its own positions, off, accessory, on and start, and a mechanical steering lock that engages when the key is removed. The locksmith checks how the barrel behaves at each stop: whether it reaches start cleanly, whether the wheel locks and releases as it should, and whether the transition back to accessory is smooth. A fault confined to one position often narrows the cause before any part comes off the vehicle.
Cutting and matching new keys
New keys are cut from the fresh pinning rather than copied from a worn original, so they engage the wafers cleanly from the first use. Where the vehicle's doors and trunk already share the ignition's key, those cylinders are brought into the same pattern so a single key continues to operate every lock on the vehicle. Each new key is tested in the ignition and in every other lock before the visit ends.
A record worth keeping
Whether the vehicle is yours long-term or recently purchased, a plain account of what was done to the ignition is worth holding onto: which parts were replaced, how many keys were cut, and whether the doors were brought onto the same key. It is a useful line in the vehicle's history file, and a straightforward thing to hand to an insurer, a future buyer or a mechanic who asks about it later.
Ignition Lock Repair
In the van
- Key code reader
- Keyed-alike pinning kit
- Pick and tension tools
- Key blanks and cutting machine
- Trim clips and fasteners
What affects the quote
Same fees day, night or weekend
1Service in place versus full replacement
Cleaning, freeing and lubricating an existing cylinder is a lighter job than removing a barrel that is cracked, seized or too worn to trust, pinning a new one, and refitting everything around it afterward.
2Keying other locks to match
Bringing the doors and trunk onto a newly pinned ignition key, so one key runs the whole vehicle again, is separate work from the ignition repair itself, even when it happens during the same visit.
3Whether an electronic diagnosis is also needed
When the mechanical repair alone does not account for everything the vehicle is doing, checking the immobilizer or transponder side becomes a separate task, priced and scoped apart from the lock cylinder itself.
Ignition Lock Repair: questions
Is my vehicle's security system disabled while this work is happening?
No part of the vehicle's electronic security system is bypassed or defeated as part of a mechanical ignition repair. The locksmith works on the physical cylinder and its housing, and any question involving the immobilizer or transponder system is identified and referred rather than worked around, so the vehicle's built-in protection stays exactly as it was designed to work.
How many keys will I leave with?
That depends on what you ask for and what the vehicle already has. A single working key is enough to drive away, but most people ask for at least one spare cut and tested at the same time, especially if the visit started because the only working key had worn down badly or snapped off inside the ignition altogether.
What is the difference between this and being locked out of my car?
A lockout is about getting into a vehicle that is closed against you; ignition lock repair is about the mechanism the key turns once you are already inside or once the door is open. The two sometimes happen together, a stuck ignition can follow a lockout, but a working ignition and a locked door are separate problems with separate tools and separate visits to arrange.
Car Keys
- Car Key ReplacementThe fob went through the washing machine in a jacket pocket.
- Spare Car Key DuplicationA teenager just passed a driving test and reasonably wants a key of their own rather than…
- Key Fob ProgrammingThe remote clicks the way it always has, but the vehicle no longer locks, unlocks or answers with…
Ignition Lock Repair near you
One team handles every service on this page for Toronto, so a lockout can turn into a rekey, and a rekey into a properly set deadbolt, within the same visit if you want it. Each service is described separately below, but at the door they fit together as one piece of work.